Mac pro 2008 rear panel




Recommended Posts

95 Comments

I recommend this method because it allows for expansion and it makes everything clean. Others have just connected the cables directly to the MB, which I tried at first and turned out to be more difficult than building this. I got mine from cpustuff.

These need to be the left angle cables, not the standard right angle ones one side has a left angle, the other is straight, I bought all short ones to keep cable clutter to a minimum because space is tight. Even if you plan on using just 2 HD's its good to use this setup to allow for expansion in the future. The 2 long cables are for connecting the optical drives, you can use 1 right-angle cable for the top drive, and 1 normal cable for the lower drive if you have one, I didn't.

Aquamac did it here. Lets begin. The two hardest aspects of this build is physically modding the case and getting the front panel to work. I will try to elaborate as much as possible on my configurations but a lot of it will come from trial and error. Let me stress that everything is this case is a tight fit and will require extensive modifications.

inrojovi.tk

Mac Pro (Mid 2012 and earlier): How to remove or install memory

I will not get too much into the cutting of the case part because if you don't know how to work with metal you should not be doing this. The Mac Pro case is actually quite fragile and very susceptible to scratches and dents. The good news it that with my setup, I only had to cut out a piece of the bottom and back part for the ports. Everything else was left in tact. There are several steps to this process, I followed them in this order and thought it was the best way to go about doing it:. Remove all of the motherboard standoffs that would go underneath your motherboard if they are not directly underneath your board leave them in.

Gently rock them back and forth with a large pair of plyers until they snap off.

Mac Pro (Early 2008) - Technical Specifications

Use the screws to connect them to your motherboard and place it inside of the case to get an idea of how it will fit. Draw an outline on the bottom of the case to get an idea of where to cut. The aluminum as actually thin enough if you have a nice pair of big sharp snips. The snips will bend the edges of the case depending on how you cut it. Once you have completed the bottom of the case take the measurements for the rear ports.

I then used the plate that came with my motherboard. Take a look at the pictures for more details. I had to make this piece 3 times before I got it right. I used an agle grinder to recess it around the outside so that a small piece would stick out of the back and cover up the edges of the place where I cut the case. There are a few models of the front panel out there. I have the early model, which supposedly is more problematic.

I didn't have any problems except for audio see below. Take a look at this thread for some more info, I have the board on the right which supposedly doesn't work. I can't stress enough the importance of making the custom PCB, otherwise you will have problems making the connections, especially with the USB. Since our power supply gives us 3, 5. Update- it seems that using this method it only provides power to 1 USB port at a time. I recommend tapping into the MB power supply extension with a split SATA power extension cable that has all 5 cables on it.

This will allow our connection to be very clean, and more importantly not destroy out PSU cable should we ever need to do a warranty exchange. For the power side of this connector, The pins run is sets of 3, so the first 3 pins are 3. I had to bend all three pins into 1 hole on the PCB because of the spacing. I'm not going to go into details on this, as there are plenty of threads out there that do it better than me.

Mac Pro (Early ) - Technical Specifications

Here is one that I ended up using that I liked the most. There is a new bootloader out there available in the package that I used. When the computer is fresh and you have not yet turned it on, boot it into target disk mode the first time and just make a copy of the hard drive before it get gunked up with user files. I used this image to restore to my new HD, ran a system update, and then installed , even before booting into that drive. Update- this is all old, you should be looking for a Zapro made a very clean-looking Mac Pro mod that involved removing half of the dividing panel rather than cutting into the bottom of the case.

You loose two HD ports this way, but at least his cables are much cleaner. Multitechparts these guys are the best, they can supply you with all of your Apple parts. You need to be a member in order to leave a comment. Sign up for a new account in our community. It's easy! Already have an account?

Sign in here. Existing user? Sign in anonymously. Or sign in with one of these services Sign in with Facebook. Sign in with Twitter. Posted March 12, Highlights of this build: I was able to use all 4 HD Bays, something others have not been able to do with a full ATX board, by experimenting with various cable configurations. Original apple IR receiver something the Mac pro does not have. Original apple Wireless I will refer to this as the "Custom PCB" from here on out. Fully modular setup: Original Mac Pro case and Apple components: Multitechparts - check their latest prices, these guys are absolutely terrific.

Extremely fast shipping, great prices, they respond to emails with lightning speed and are very friendly.. I gave them my build list so they should have a custom auction that will have all of the Apple parts you will need to build this unit. If they still have the build then it is by far the cheapest and easiest solution for getting all of these parts.

Apple Mac Pro Chassis Case The part number probably doesn't matter for this. I think most of them are the same.

Mine was the early model they have all been more or less the same since Speaker Fan Guide Assembly This is the internal speaker for the unit. Not necessary if you don't plan on using the additional 2 fans up front, but I also mounted my IR board to this, as it provides a nice surface on the front. If you don't use it you will need to buy a cheap internal speaker. Power Supply Cable Cover This is great to keep your PS cables tucked behind the optical drive. It's a tight fit but makes everything much cleaner. Mac Pro Hard Drive Carrier You will need these to hold your hard drives. Mac Pro Front Fan This is the fan holder that will hold 2 front mm case fans.

I have not finished this part of the project yet. The original apple ones will need to be modified, I will update this post once I have completed this. There are many threads out there about this issue, if you figure out an easy solution, would be great to hear about it. Optical Drive Carrier This will hold your optical drive s. Mac Pro Front Panel. I will talk more about this later; there are different models with different pinouts. Mac Pro Front panel Audio cable. Front Fan Assembly Early GPU Graphics Card.

Graphic Card for Mac Pro Early Hard drives and hard drive carriers Early Memory Cage with Rear Fan Early Opening the Computer Early Optical Drive.


  • Mac Pro (First Generation) Repair (, , ) - iFixit.
  • Apple Footer.
  • como descargar e instalar skyrim para mac?
  • Choose your model.
  • Applicable models;
  • 1 post in this topic!

Processor Heatsink Cover Early In Progress Guides MacPro fan removal. Graphics Card. Support Questions Ask a Question. Tools These are some common tools used to work on this device. Phillips 1 Screwdriver. Anti-Static Wrist Strap. Phillips 0 Screwdriver. Large Needle Nose Pliers.

Mako Driver Kit - 64 Precision Bits. Phillips 2 Screwdriver. Arctic Silver Thermal Paste. Documents Mac Pro Early

mac pro 2008 rear panel Mac pro 2008 rear panel
mac pro 2008 rear panel Mac pro 2008 rear panel
mac pro 2008 rear panel Mac pro 2008 rear panel
mac pro 2008 rear panel Mac pro 2008 rear panel
mac pro 2008 rear panel Mac pro 2008 rear panel

Related mac pro 2008 rear panel



Copyright 2019 - All Right Reserved